Visonic POWERMASTER-10 - INSTALLER GUIDE Guide de l'utilisateur télécharger pdf (Page 27)

MENUS AND FUNCTIONS

26 D-303223 PowerMaster-10/30 G2 User's Guide

If Partition is enabled, continue to step 6 (applicable to PowerMaster-30 G2 only).

You can now enroll another proximity tag. You can also select another option in the User Settings menu

(see section B.1 and section B.2), or quit programming (see section B.3).

If no proximity tag is enrolled in the system, the display reads [

NO EXISTING DEV.

To abort the procedure, press the button.

This setting can be performed only after completing steps 1 - 5 of section B.5A.

The



symbol now appears next to the newly selected Partitions.

You can now repeat steps 2 - 7 to program or edit another Proximity tag.

You can now add or delete another proximity tag. You can also select another option in the User Settings

menu (see section B.1 and section B.2), or quit programming (see section B.3).

B.6 Add / Delete Keyfob Transmitters

A portable keyfob transmitter may be assigned to each of the PowerMaster-10 G2 user codes 1-8 /

PowerMaster-30 G2 user codes 1-32 for better, quicker and safer arming/disarming and other control functions.

Each keyfob should be assigned with a serial No. 1-8 (PowerMaster-10 G2) / 1-32 (PowerMaster-30 G2) and

enrolled into the system correspondingly.

Partition Option



(For information about Partition option - see Appendix B)

If the Partition option is enabled in the control panel, each of the 32 keyfobs can be authorized by the Master

User to arm and disarm any combination, or all 3 partitions, irrespective of the authorization of its corresponding

user code.

 Here you can add (enroll) the 8 (PowerMaster-10 G2) / 32 (PowerMaster-30 G2) Keyfob transmitters and

define which of the 3 partitions each of the keyfob will be authorized to arm and disarm, or delete keyfobs as

required.



1. Before anything else, gather up all keyfob units you intend to enroll and make sure they all have

batteries installed and that they are active (the LED blinks upon pressing any of the buttons).

2. Carefully read the section titled "Additional Information" according to the indicated references

etc –

see table at end of this section.

A. To Add (Enroll) a Keyfob

Enter the [USER SETTINGS] menu, select the [KEYFOBS] option and press

The display will read [ADD NEW KEYFOB].

To enroll a new keyfob press

The display offers you two alternative methods to enroll a keyfob:

A: ENROLL NOW: Press and hold the AUX  button on the selected keyfob

until the LED is constantly on.

This procedure completes the enrollment.

4a.

☺ Go to step 5

If enrollment was successfully completed, a "Happy Tune" ☺ sounds and

the display reads [DEVICE ENROLLED] for a short duration and then

changes to read the keyfob's details. Continue to step 5.

4b.

B: ENROLLMENT BY DEVICE ID: Enter the 7-digit number that appears on

the keyfob sticker and then press to confirm. To complete the

enrollment procedure, see Note 9 in the Additional Information table below.

☺ Go to step 5

If a valid ID was entered, a "Happy Tune" ☺ sounds and the display reads

[ID ACCEPTED] for a short duration and then changes to read the keyfob's

details. Continue to step 5.

The display shows the allocated keyfob serial No (user No.), which is always



Refers to PowerMaster-30 G2 only

KEYFOBS

ADD NEW KEYFOB

ENROLL NOW or

ENTR ID:xxx-xxxx

DEVICE ENROLLED

ID No. 300-5786

ID ACCEPTED

F01:keyfob

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 61 62

Commentaires sur ces manuels

Pas de commentaire

Visonic POWERMASTER-10 - INSTALLER GUIDE Guide de l'utilisateur Page 27

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Visonic POWERMASTER-10 - INSTALLER GUIDE