Visonic POWERMASTER-10 Guide de l'utilisateur télécharger pdf (Page 86)

APPENDIX F. PowerLink3 IP Communicator,

D-304762 PowerMaster-10/30 G2 Installer's Guide

F3. Installation

Package Contents

1 x Visonic PowerLink3 IP Communicator

1 x 2m (6.5 feet) Cat-5 Cable

1 x RS-232 Cable

System Requirements

• PowerMaster Security System.

• High-Speed Internet connection (Cable or DSL) enabled via a Home Router (Ethernet Based).

• One free Ethernet port on the home router for the PowerLink3 IP Communicator connection.

F4. Installing the Visonic PowerLink3 IP Communicator

Perform the following instructions for the Visonic PowerLink3 IP Communicator hardware installation:

Note PowerLink3 IP Communicator operation is not backed up by the control panel's battery and it is shut down during

AC failure.

1 2 ... 81 82 83 84 85 86 87 88 89 90 91 ... 95 96

PowerMaster-10/30 G2 1
Version 17 1
1. INTRODUCTION 3
Figure 3.2 –Phone Wiring 9
3.4 GSM Module Installation 10
3.5 PGM-5 Installation 11
Figure 3.6a – Cable Wiring 12
UL listed 13
PGM: not to be enabled in UL 13
Figure 3.7a - Power Cable 14
Connection 14
Figure 3.9 - Final Closure 16
Figure 4.3a – Phone Wiring 18
4.6 GSM Module Installation 20
4.8 PGM-5 Installation 21
Figure 4.9a –Expander Module 22
Figure 4.9b – Zone 23
and Siren Wiring 23
4.11 Battery Insertion 25
Figure 4.13 26
5. PROGRAMMING 27
 [1] in Step 1 above) 28
5.2.2 Selecting options 28
– Exiting the Installer Mode 29
– Setting Installer Codes 29
5.4 Zones / Devices 30
Part B - Configuration 31
- Configuring New Devices 32
5.4.3 Deleting a Device 34
5.4.5 Replacing a Device 34
– Replacing a Device 35
– Changing Defaults 35
5.5 Control Panel 36
01:ENTRY DELAY1 37
02:ENTRY DELAY2 37
VOICE REPORT 38
SMS REPORT 38
09:ARMING KEY 39
21:SWINGER STOP 39
22:CROSS ZONING 39
38:CANCEL ALARM 41
39:ALARM RESET 41
40:ABORT FIRE T 41
43:PANEL SIREN 41
44:SIREN TIME 41
5.6 Communication 44
PowerMaster String Editor 48
Event Reporting Chart 51
IMAGE FORWARD 52
1st e-mail 52
2nd e-mail 52
5.6.8 Broadband 54
5.7 PGM Output 55
5.8 Custom Names 56
5.8.2 Record Speech 57
5.8.3 Voice Box Mode 57
5.9.4 Testing the SIM Number 60
5.10 User Settings 61
5.11 Factory Default 61
5.12 Serial Number 61
5.13 Start UL/DL 62
5.14 Partitioning 62
5.15 Operation Mode 62
5.15.2 Select setting 63
5.15.3 BS8243 Setup 63
5.15.4 DD243 Setup 64
5.15.5 CP01 Setup 66
5.15.6 OTHERS Setup 67
6. PERIODIC TEST 68
7. MAINTENANCE 70
7.4 Fuse Replacement 72
7.6 Annual System Check 72
8. READING THE EVENT LOG 73
APPENDIX A. Specifications 74
A2. Wireless 75
A3. Electrical 75
A4. Communication 76
A5. Physical Properties 77
B2. Common Areas 78
Assignments 79
C2. Keyfob Transmitter List 80
APPENDIX D. Event Codes 82
Type Number Range 83
APPENDIX E. Sabbath Mode 84
F1. Getting Started 85
F2. Specifications 85
F3. Installation 86
Hardware Installation 87
Control Panel Configuration 89
APPENDIX G. Glossary 90
Compliance with 92
Standards 92
WARRANTY 93
Initiating Alarms 95
Preparing to Arm 95
Zone Bypass Scheme 96

Commentaires sur ces manuels

Pas de commentaire

Visonic POWERMASTER-10 Guide de l'utilisateur Page 86

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Visonic POWERMASTER-10