Visonic POWERMASTER-10 Guide de l'utilisateur télécharger pdf (Page 36)

5. PROGRAMMING

D-304762 PowerMaster-10/30 G2 Installer's Guide

5.4.7 Configuring Soak Test Mode

This option enables you to enter device zones into Soak Test mode.

To Enable the Soak Test proceed as follows:

Step 1



Step 2



Step 3



Step 4



Step 5



Select "ADD TO

SOAK TEST" Option

[1] Select the respective

device Group

[2] Select device zone

number

[3] Select to enable or

disable the Soak Test

[4]

[5]



02:ZONES/DEVICES CONTACT SENSORS

Z09:Motion Sens

ID No. 120-2468

 

ADD TO SOAK TEST

MOTION SENSORS

Disable test



Enable test

See 

[5]





 to

Step 3



– Enabling Soak Test mode

[1] Enter the Installer Menu, select the "02.ZONES/DEVICES" option (see section 5.2) and then select the "ADD TO

SOAK TEST" option.

[2] Select the respective Group of the device you wish to add the Soak Test. For example, "MOTION SENSORS".

[3] Scroll to select the specific device zone number.

[4] Select between “Disable test” (default) or “Enable test”.

[5] If set to “Enable Test” you must set the duration of the Soak Test before the Soak Test will start (see Section

5.5.8). You can stop the test for the relevant zone by changing the setting to "Disable test" at any time during the

testing period. All Soak test zones will be reset to start a new test upon occurrence of one of the following: 1)

Power up of the system; 2) Setup of Factory Default; 3) Change in system Soak Time.

5.4.8 Updating Devices after Exiting Installer Mode

When exiting the "Installer mode", the PowerMaster panel communicates with all devices in the system and updates

them with the changes that have been performed in their "Device Settings" configuration. During the updating period,

the display indicates "DEV UPDATING 018" where the number (for example, 018) is a countdown of the remaining

number of devices yet to be updated.

5.5 Control Panel

5.5.1

General Guidance – "Control Panel" Flow-Chart & Menu Options

The "CONTROL PANEL" menu enables you to configure and customize the operation of the control panel. The

"CONTROL PANEL" menu provides you with configurable parameters divided into several groups, each dealing with

certain aspects of the system operations as follows (see detailed list in Step 2 of the chart below):

Group Description of Group Features and Parameters Section

Arming/Disarming

and Exit/Entry

Procedures

Contains configurable features and parameters related to Arming and Disarming of the

system and the Exit and Entry procedures.

5.5.2

Zone Behavior

Contains configurable features and parameters related to the functionality of the Zones. 5.5.3

Alarms &

Troubles

Contains configurable features and parameters related to initiating, canceling and

reporting of Alarm and Trouble events.

5.5.4

Sirens

Contains configurable features and parameters common to all sirens in the system.

5.5.5

User Interface

Contains configurable features and parameters related to the functionality of the panel's

audible and visual indications.

5.5.6

Jamming &

Supervision

Contains configurable features and parameters related to detecting and reporting of RF

Jamming and device Supervision (missing device) events.

5.5.7

Miscellaneous

Contains a variety of other configurable features and parameters related to the system.

5.5.8

Soak Test is not applicable for UL installations.

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 95 96

Commentaires sur ces manuels

Pas de commentaire

Visonic POWERMASTER-10 Guide de l'utilisateur Page 36

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Visonic POWERMASTER-10