Visonic POWERMASTER-10 - INSTALLER GUIDE Spécifications Page 59
- Page / 82
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5. PROGRAMMING
58 D-303222 PowerMaster-10/30 G2 Installer's Guide
The following table presents the test result messages
Message
Description
Unit is OK
GSM / GPRS is functioning correctly
GSM comm. loss
GSM/GPRS module does not communicate with the Panel
Pin code fail
Missing or wrong PIN code. (Only if SIM card PIN code is enabled.)
GSM net. fail
Unit failed with registration to local GSM network.
SIM card fail
SIM not installed or SIM card failure.
GSM not detected
GSM auto enroll failed to detect GSM/GPRS module.
No GPRS service
The SIM card does not have the GPRS service enabled.
GPRS conn. fail
Local GPRS network is not available or, wrong setting to GPRS APN, user and/or password.
Srvr unavailable
PowerManage receiver cannot be reached – Check the Server IP
IP not defined
Server IP #1 and #2 are not configured.
APN not defined
APN is not configured.
SIM card locked
After entering a wrong PIN code 3 consecutive times the SIM is locked. To unlock it enter a PUK
number. The PUK number cannot be entered by the control panel.
Denied by server
PowerManage denies the connection request. Check that the panel is registered to PowerManage
5.10 User Settings
This USER SETTINGS menu provides you with a gateway to the user settings through the regular user menus.
Refer to the PowerMaster User's Guide for detailed procedures.
Caution! If after having programmed the user codes the system does not recognize your installer code, this
indicates you must have programmed a user code that is identical with your installer code. If so, access the user
menu and change the code that is identical with your installer code. This will re-validate your installer code
5.11 Factory Default
The FACTORY DEFLT menu enables you to reset the PowerMaster parameters to the factory default parameters. To
obtain the relevant parameters defaults, contact the PowerMaster dealer. Reset factory default parameters as follows:
Step 1
Step 2
Step 3
Step 4
Step 5
Select "09:FACTORY DEFLT"
menu
Select "<OK> to restore"
Enter Installer Code
Resetting of factory default
parameters is underway
09:FACTORY DEFLT
<OK> to restore
ENTER CODE:
PLEASE WAIT…
to Step 1
Note: For PowerMaster with 2 installer codes, INSTALLER code and MASTER INSTALLER code, only the master
installer code enables to perform the factory default function.
5.12 Serial Number
The SERIAL NUMBER menu enables reading the system serial number and similar data for support purposes only. To
read the system serial number and other relevant data proceed as follows:
Step 1
Step 2
Step 3
Select "10:SERIAL
NUMBER" menu
[1]
Click next repeatedly to view
relevant data.
[2]
10:SERIAL NUMBER
to Step 1
Definition
0907030000.
Control panel serial number
JS702275 K16.010
Control panel software version
JS700421 v1.0.01
1
Control panel LCD software
version
PANEL ID 100005
Control panel ID for
PowerManage connectivity
PYTHON:
GSM image transfer software
version
J-702271 K16.010
Control panel default version
1
Refers to PowerMaster-30 G2 only
- INSTALLER GUIDE 1
- PowerMaster-10/30 G2 2
- Version 16 2
- Installer's Guide 2
- 1. INTRODUCTION 4
- Figure 3.2 –Phone Wiring 10
- 3.4 GSM Module Installation 11
- 3.5 PGM-5 Installation 12
- Figure 3.6a – Cable Wiring 13
- Figure 3.7a - Power Cable 15
- Connection 15
- Figure 3.9 - Final Closure 17
- Figure 4.3a – Phone Wiring 19
- Figure 4.6 21
- Figure 4.9a –Expander Module 23
- Figure 4.9b – Zone 24
- and Siren Wiring 24
- 4.11 Battery Insertion 26
- Figure 4.13 27
- 5. PROGRAMMING 28
- [1] in Step 1 above) 29
- 5.2.2 Selecting options 29
- or 30
- 5.4 Zones / Devices 31
- Part B - Configuration 32
- - Configuring New Devices 33
- 5.4.3 Deleting a Device 35
- 5.4.5 Replacing a Device 35
- 5.5 Control Panel 37
- VOICE REPORT 39
- SMS REPORT 39
- 5.6 Communication 44
- String Editor Functionality 47
- Voice <- -> C.S 51
- Ringback time 51
- Ambient level 51
- Mast. UL/DL code 53
- Inst. UL/DL code 53
- 5.7 PGM Output 54
- Zone B Z:_ _ 55
- Zone C Z:_ _ 55
- 5.8.2 Record Speech 56
- 5.9.3 Testing the GSM module 58
- 5.10 User Settings 59
- 5.11 Factory Default 59
- 5.12 Serial Number 59
- 5.13 Start UL/DL 60
- 5.14 Partitioning 60
- 5.15 Operation Mode 60
- 5.15.3 BS8243 Setup 61
- 5.15.4 DD243 Setup 62
- 6. PERIODIC TEST 63
- <location> 65
- 7. MAINTENANCE 66
- 7.4 Fuse Replacement 67
- 8. READING THE EVENT LOG 68
- APPENDIX A. Specifications 69
- A2. Wireless 70
- A3. Electrical 70
- A4. Communication 71
- A5. Physical Properties 71
- (optional) 72
- Assignments 73
- APPENDIX D. Event Codes 75
- D2. SIA Event Codes 76
- APPENDIX E. Sabbath Mode 77
- APPENDIX F. Glossary 78
- Compliance with 80
- Standards 80
- WARRANTY 81
- PowerMaster-30 G2 82
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Visonic POWERMASTER-10 - INSTALLER GUIDE
(9 pages)Robin America R600 manuels
Manuels d'utilisation et guides de l'utilisateur pour Générateurs d'électricité Robin America R600.
Nous fournissons des manuels en pdf 1 Robin America R600 à télécharger gratuitement par type de document : Spécifications
Commentaires sur ces manuels