Visonic POWERMASTER-10 - INSTALLER GUIDE Spécifications télécharger pdf (Page 13)

3. POWERMASTER-10 G2 INSTALLATION

12 D-303222 PowerMaster-10/30 G2 Installer's Guide

3.6 Adding Wired Zones or PGM Device

Required tools: Cutter and slotted screwdriver - 3 mm blade.

PowerMaster-10 G2 wiring is shown in Figures 3.6a – 3.7b.

CABLES ROUTING GUIDE

A. Cables entry options

B. Back unit

C. Cable clips

To Route the Cable:

1. Remove the left or

right side cables

entry knockout(s)

and enter the

required cable(s)

2. Remove and use as

cable clamp(s)

To Route the Cable (continued):

3. Position the clamp (1 of 2) as shown and then rotate into place.

4. Using a slotted screwdriver press downward gently on the point illustrated in the drawing. Make sure the clamp is

locked (a click is heard).

Figure 3.6a – Cable Wiring

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 81 82

INSTALLER GUIDE 1
PowerMaster-10/30 G2 2
Version 16 2
Installer's Guide 2
1. INTRODUCTION 4
Figure 3.2 –Phone Wiring 10
3.4 GSM Module Installation 11
3.5 PGM-5 Installation 12
Figure 3.6a – Cable Wiring 13
Figure 3.7a - Power Cable 15
Connection 15
Figure 3.9 - Final Closure 17
Figure 4.3a – Phone Wiring 19
Figure 4.6 21
Figure 4.9a –Expander Module 23
Figure 4.9b – Zone 24
and Siren Wiring 24
4.11 Battery Insertion 26
Figure 4.13 27
5. PROGRAMMING 28
 [1] in Step 1 above) 29
5.2.2 Selecting options 29
 or 30
5.4 Zones / Devices 31
Part B - Configuration 32
- Configuring New Devices 33
5.4.3 Deleting a Device 35
5.4.5 Replacing a Device 35
5.5 Control Panel 37
VOICE REPORT 39
SMS REPORT 39
5.6 Communication 44
String Editor Functionality 47
Voice <- -> C.S 51
Ringback time 51
Ambient level 51
Mast. UL/DL code 53
Inst. UL/DL code 53
5.7 PGM Output 54
 Zone B Z:_ _ 55
 Zone C Z:_ _ 55
5.8.2 Record Speech 56
5.9.3 Testing the GSM module 58
5.10 User Settings 59
5.11 Factory Default 59
5.12 Serial Number 59
5.13 Start UL/DL 60
5.14 Partitioning 60
5.15 Operation Mode 60
5.15.3 BS8243 Setup 61
5.15.4 DD243 Setup 62
6. PERIODIC TEST 63
 <location> 65
7. MAINTENANCE 66
7.4 Fuse Replacement 67
8. READING THE EVENT LOG 68
APPENDIX A. Specifications 69
A2. Wireless 70
A3. Electrical 70
A4. Communication 71
A5. Physical Properties 71
(optional) 72
Assignments 73
APPENDIX D. Event Codes 75
D2. SIA Event Codes 76
APPENDIX E. Sabbath Mode 77
APPENDIX F. Glossary 78
Compliance with 80
Standards 80
WARRANTY 81
PowerMaster-30 G2 82

Commentaires sur ces manuels

Pas de commentaire

Visonic POWERMASTER-10 - INSTALLER GUIDE Spécifications Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Visonic POWERMASTER-10 - INSTALLER GUIDE