Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE Manuel d'installation télécharger pdf

PowerMax+

Introduction

Welcome to PowerMax+, the wireless Home Security solution.

This guide provides some step by step information that will help

you get the system up and running.

Before you begin you should know that this kit is supplied with

the transmitters pre-enrolled and pre-programmed with the

most common settings. Additionally, each transmitter is labelled

with its zone or fob number on the rear plastic. Following this

guide will help you make basic conguration changes, for more

detailed information please refer to the full programming guide

included within the kit.

Finally….we have included a trouble shooting section to this

guide. BEFORE you ring the support line have a look through as

most common problems are listed here.

1) To Access the installer mode via the user menu. Press

until the display shows “User settings”, then press

and

enter the user code. Once in the user menu press

twice until

the display shows installer mode, then press

followed by

the installer code.

Default codes are :- User 1111 / Installer 9999. L

Whilst in any of the menus (user or installer) the following keys

will help you navigate the systems:-

– returns you to the start of the main menu.

– takes you back to the previous menu

– scrolls forward in the menu

– scrolls back in the menu

2) Choose a location to mount your control panel,

making sure it is at least 1m from any large metallic objects e.g.

Radiators, or RF equipment e.g. WiFi transmitters. Additionally

ensure there is access to a mains power supply and telephone

line if required.

Remove the bracket from the main control panel by undoing the

screw located at the bottom of the panel. Mark and x as required

using three xing points. Once done install the transformer,

remove the Euro plug and connect to the mains point via a 3pin

plug (not supplied) or for EN-50131 systems an unswitched fuse

spur (not supplied)

This is a professional product and is not suitable for DIY L

installation

QuickFit Kit Easy Start Guide

STOP!

Make a cup of tea, and spend the next

five minutes reading this information”.

Keypad cover

(closed)

Control keys

Display

Luminous

indicators

Microphone

Built-in siren

Battery

compartmemt

cover (closed)

Bracket screw

1 2 3 4

Résumé du contenu

Page 1 - PowerMax+

PowerMax+IntroductionWelcome to PowerMax+, the wireless Home Security solution. This guide provides some step by step information that will hel

Page 2 - K-985 MCW

3) (Optional) Connect the Powermax to the telephone line via terminals 2 & 5 on the BT socket, and the “Line” terminals on Powermax. Alternatively

Page 3

Trigger a tamper on the sensor, trigger the input (for universal • or aux input on door contacts) or press button (for hand held devices) to initiate

Page 4 - QuickFit Kit Easy Start Guide

12341 22134Away1 Home2 Disarm3 Aux4 + Panic (if enabled) QuickFit Kit Easy Start Guide9) Trouble ShootingQ – Display - The system display show

Plus de documents pour Logiciel Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE

Voir le document Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE Guide de l'utilisateur

Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE Guide de l'utilisateur (4 pages)

Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE Guide de l'utilisateur (87 pages)

Voir le document Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE Manuel d'utilisateur

Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE Manuel d'utilisateur (10 pages)

Commentaires sur ces manuels

Pas de commentaire

Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE Manuel d'installation

Naviguer en ligne ou télécharger Manuel d'installation pour Logiciel Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE. Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE Installation manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Logiciel Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Visonic POWERMAX REMOTE - PROGRAMMER SOFTWARE