Visonic PowerMax10 Spécifications télécharger pdf

DE5450 PowerMax Installation Instructions

POWERMAX

POWERMAXPOWERMAX

POWERMAX

Fully Supervised Wireless Alarm Control System

Installation Instructions

TABLE OF CONTENTS

TABLE OF CONTENTSTABLE OF CONTENTS

TABLE OF CONTENTS

1. INTRODUCTION ............................................................ 2

2. SPECIFICATIONS ....................................................... 2

2.1 General Data ........................................................... 2

2.2 RF Section .............................................................. 2

2.3 Electrical Data ......................................................... 2

2.4 Communication ....................................................... 3

2.5 Physical Properties ................................................. 3

3. INSTALLATION ............................................................ 3

3.1 Unpacking the Equipment....................................... 3

3.2 Supplying Power to the Unit ................................... 3

3.3 Programming .......................................................... 3

3.4 Mounting ................................................................. 3

3.5 Wiring ...................................................................... 3

3.6 Connecting the AC Transformer ............................. 3

3.7 PowerMax-Compatible Detectors ........................... 5

3.8 PowerMax-Compatible Transmitters ...................... 5

3.9 Mounting the RS232 Module .................................. 6

3.10 Installing an Optional X-10 Siren .......................... 6

4. TESTING PROCEDURES ............................................ 6

4.1 Preparations ........................................................... 6

4.2 Diagnostic Test ....................................................... 6

4.3 Keyfob Transmitter Test ......................................... 7

4.4 Appliance ON/OFF Test ......................................... 7

4.5 Emergency Transmitter Test .................................. 7

5. MAINTENANCE ........................................................... 7

5.1 Dismounting the Control panel ............................... 7

5.2 Replacing the Backup Battery ................................ 7

5.3 Fuse Replacement ................................................. 8

5.4 Replacing/Relocating Detectors ............................. 8

APPENDIX A. DETECTOR DEPLOYMENT AND

TRANSMITTER ASSIGNMENTS ...................................... 8

A.1 Detector Deployment Plan ..................................... 8

A.2 Keyfob Transmitter List .......................................... 9

A.3 Emergency Transmitter List ................................... 9

A.4 Non-Alarm Transmitter List .................................... 9

APPENDIX B. X-10 UNIT ASSIGNMENTS ....................... 9

FCC STATEMENTS ........................................................ 10

DECLARATION OF CONFORMITY ................................ 11

MESSAGE TO THE INSTALLER

The PowerMax control panel is supplied with 3 instruction manuals:







Installation Instructions (this manual - for your exclusive use)







Programming Guide (for your exclusive use)







User’s Guide (for your use during installation only. Must be handed over to the master user after testing the system).

Appendices A and B to the installation instructions will help you prepare an installation plan. Please take time to fill out the

forms - your job will become much easier and confusion will be prevented. Filling out the forms will also help you create a

list of detectors and transmitters that must be obtained for the particular application. Compatible detectors and

transmitters are listed and described briefly in Paragraphs 3.8 and 3.9 of this manual.

Remember - it is advisable to power up the control panel temporarily after unpacking and program it on the work bench, in

accordance with the installation plan. Paragraph 3.3 of this manual refers you to the programming guide.

The programming flow charts in the programming guide show all options available for each parameter. Factory defaults

are marked with a dark box to their right, and other options (that can be selected instead) are marked by clear boxes. This

method allows you to put a checkmark in the appropriate clear box whenever you deviate from the factory defaults.

To increase the backup time provided by the Ni-Cd battery (which is 4 -6 hours), we recommend the use of 6 size AA Ni-

Mh cells with a capacity of 1600 mAh (produced by GP). Under AC failure conditions, these batteries provide up to 20-

hour backup with no alarms, and up to 16 hours if an alarm occurs.

Although setting the correct time and date is one of the user tasks, we recommend that you set the time and date in the

course of programming. Access to the “User Settings” is possible through item 9 on the installer‘s menu (see User’s

manual for exact procedure).

When you are through programming, proceed to install the system as detailed in the Installation Instructions, from

paragraph 3.4 onward.

The installer should verify line seizure. Be aware of other phone line services such as DSL.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - Installation Instructions

DE5450 PowerMax Installation Instructions 1 POWERMAXPOWERMAXPOWERMAXPOWERMAX Fully Supervised Wireless Alarm Control System Installation Instruc

Page 2 - 2.3 Electrical Data

10 DE5450 PowerMax Installation Instructions Federal Communications Commission (FCC) Statements FCC PART 15 STATEMENT This device complies with Part

Page 3 - 3. INSTALLATION

DE5450 PowerMax Installation Instructions 11

Page 4 - Figure 3 - Mounting

12 DE5450 PowerMax Installation Instructions WARRANTY Visonic Limited (the “Manufacturer") warrants this product only (the "Product"

Page 5 - RJ-11 plug

2 DE5450 PowerMax Installation Instructions 1. INTRODUCTION1. INTRODUCTION1. INTRODUCTION1. INTRODUCTION The PowerMax is a user and installer-frien

Page 6 - 4.2 Diagnostic Test

DE5450 PowerMax Installation Instructions 3 Backup Battery (provides power for at least 4 hours) Option 1 - 9V, six alkaline AA cells, 1.8 Ah Opti

Page 7 - 5. MAINTENANCE5. MAINTENANCE

4 DE5450 PowerMax Installation Instructions ScrewholesScrewholesMark and drill 4 holes inmounting surface. Insertwall anchors and fasten thebracke

Page 8 - A1. Detector Deployment Plan

DE5450 PowerMax Installation Instructions 5 NOTE: PSC-04 IN THE U.S. AND CANADA,ALTERNATIVE MODELS ELSEWHERE.0.5ACOM+INT -EXT -2.2 kΩE.O.L.MAGNETICC

Page 9 - A2. Keyfob Transmitter List

6 DE5450 PowerMax Installation Instructions The PowerMax system is compatible with multi-button and single button key-ring and hand-held transmitters

Page 10 - FCC PART 68 STATEMENT

DE5450 PowerMax Installation Instructions 7 A. Click the <NEXT> button until the display reads: I N S T A L L E R M O D E B. Click <OK>

Page 11

8 DE5450 PowerMax Installation Instructions 5.3 Fuse Replacement The PowerMax has a fuse which can burn out: Siren Fuse - 0.5 A, time delay ty

Page 12 - WARRANTY

DE5450 PowerMax Installation Instructions 9 A2. Keyfob Transmitter List Transmitter Data AUX button Assignments No. Type Holder Status or Arming “

Plus de documents pour Systèmes de contrôle d'accès de sécurité Visonic PowerMax10

Voir le document Visonic PowerMax10 Guide de l'utilisateur

Visonic PowerMax10 Guide de l'utilisateur (50 pages)

Voir le document Visonic PowerMax10 Spécifications

Visonic PowerMax10 Spécifications (78 pages)

Commentaires sur ces manuels

Pas de commentaire

Visonic PowerMax10 Spécifications

Naviguer en ligne ou télécharger Spécifications pour Systèmes de contrôle d'accès de sécurité Visonic PowerMax10. Visonic PowerMax10 Specifications Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Systèmes de contrôle d'accès de sécurité Visonic PowerMax10

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Visonic PowerMax10